The filigree work on a silver hairpin is made of wire that can be thinner than a human hair, often around a tenth of a millimetre. No one can carve metal that fine, and no one can cast it: a mould that thin would not fill. The wire is made by forcing metal through a hole, over and over, until it is small enough. The process is called drawing, and it is one of the oldest metalworking operations there is.
The tool is a draw plate: a plate of hardened steel pierced with a row of holes, each one tapered like a shallow funnel and each one a little smaller than the last. The wire is tapered at one end — hammered or filed to a point — pushed through the largest hole from the wide side, gripped on the far side with pliers or a draw bench, and pulled. The tapered hole squeezes the metal as it passes and the wire comes out round, straight, and slightly smaller than it went in.
Nothing is removed. The volume of metal stays the same across the pass, so as the cross-section shrinks the length grows by the same proportion. Draw a two-millimetre rod down to one millimetre and it becomes four times as long, because the area has fallen to a quarter. That is why drawing is not a cutting process and why the scrap bin at a wire bench is almost empty: the metal is not lost, it is redistributed.
Why the wire has to be softened
Metal that has been deformed is not the same metal afterwards. Bending, rolling and drawing all push the crystal lattice past its easy motion and tangle the defects in it, which makes the metal harder and less able to deform further. This is work hardening, and it is why a paper clip snapped straight becomes stiff at the bend, and why a copper pipe work-hardens and then cracks if you keep bending it.
A drawn wire therefore gets harder with every pass, and at some point it stops stretching and starts breaking. The remedy is annealing: heat the wire until it glows a dull red, hold it briefly, and let it cool. The tangled lattice recovers, the metal becomes soft again, and the next passes can proceed. For silver this happens at a temperature a jeweller can judge by eye, which is why the process has been practical for a very long time. Between two annealings a silver wire will usually take a reduction of something like a fifth of its diameter per pass, less as it gets finer.
The arithmetic of a long draw is the thing that surprises people. Going from a two-millimetre rod to a tenth-of-a-millimetre wire is a twentyfold reduction in diameter, which means the cross-section falls by a factor of four hundred. Because each pass only takes a modest bite, that is roughly twenty-five to thirty pulls, with three or four annealings spread through them. A wire bench is not a single dramatic operation; it is a long, boring, careful one.
What the hole decides
The shape of the finished wire is the shape of the last hole it went through. A round hole gives round wire, an oval hole gives oval, a square hole gives square — and a square wire has a crisp edge that a round one cannot. This is why a draw plate is a set of standards as much as a tool: once a workshop owns a plate, every wire it makes comes out at those fixed sizes, and wire from two different benches will fit the same clasp.
Drawing also straightens. A wire that has been coiled comes off the draw bench dead straight, because it has just been pulled along its own axis under tension. That straightness is exploited: lengths of wire are drawn, cut, and used without further straightening, and any kink put in afterwards is a defect rather than a normal state.
Filigree depends on the last pass more than any other stage. After the final draw the wire is stiff, and that stiffness is what lets a coil of it stand up on its own instead of collapsing. Two strands are twisted together into a cord, the cord is rolled flat, and the flattened strip is bent into scrolls and spirals that hold their shape without solder. Cloisonné uses the same wire in a different role: there the wire is a fence standing on edge to hold enamel, and it must be soft enough to bend around a curve without kinking.
The two requirements pull in opposite directions, which is why the same workshop keeps wire annealed for one job and hard-drawn for another. A wire for a wall wants to be bent; a wire for a scroll wants to resist bending once bent. Nothing about the metal changes between those two states except how recently it was heated.
Set beside the other forming methods, drawing is unusual in how little it depends on the maker's hand. A brush is shaped by the way the hairs are combed and tied, and its quality is judged by a point that comes from the arrangement of thousands of fibres. A sheet of paper is formed by draining a slurry through a screen. Drawing is cruder and far more exact at once: the maker's only decisions are when to anneal and how much to take per pass, and the hole does the rest.
That is why the wire in a piece of filigree can be trusted to be uniform to a hundredth of a millimetre while the scroll it forms was placed entirely by eye. One half of the object is a machine product and the other half is a hand decision, and the joint between them is invisible.