A closed folding fan is a bundle of sticks. Open it with one flick of the wrist and it becomes a stiff sheet of paper that holds its own shape in the air. Nothing clicks into place, nothing locks: there is no catch, no spring, no ratchet. The fan is open because of the way it was folded, and it stays open for the same reason.

The parts are few. Two outer sticks, called guards, which are thicker than the rest and take the wear of being handled. A number of inner ribs, thin and tapered, sitting between them. One rivet through the end of all of them, at the pivot. And the leaf — paper, silk or thin cotton — pleated into as many folds as there are gaps between ribs, and glued to the ribs. That is the whole mechanism.

The pleat is a hinge. A crease in paper is a line where the material has been bent past its elastic limit, so it now prefers to fold there rather than anywhere else. Put a series of parallel creases in a sheet and you have a chain of hinges that can open and close as one. This is the same trick as a paper lantern's concertina body, and the same one used in a paper fan of the fixed kind — but a lantern is meant to hang limp, and the fan has to end up flat and rigid.

Why the leaf is glued only at the top

Here is the detail that decides whether the whole thing works. The leaf is attached to the guards along their full length, but to the inner ribs only near the top edge, along the arc. The lower part of the leaf, close to the rivet, is left free of the inner ribs. If the paper were glued to every rib all the way down, the fan could not close: the paper would have to compress into itself with nowhere to go, and the folds would tear within a few uses.

Leaving that strip free gives each fold a place to travel. As the fan closes, the leaf is not squeezed — it is folded, and the free margin slides past the ribs on either side of it. The visible consequence is the little triangular gap near the pivot on a cheap fan, where the leaf has pulled away from the ribs. That gap is not a defect; it is the clearance the mechanism needs.

Because the leaf is a continuous sheet glued across the top, the ribs cannot rotate independently. Open one gap by a few degrees and the sheet forces its neighbours to open by the same amount, because the leaf's width across the top is fixed. The fan therefore opens as one rigid body rather than as a slack chain. This is why a flick works and a slow pull also works: the speed does not matter, only that you separate the two guards.

What the guards and the rivet are for

The two guards are thicker for two reasons. They carry the pull when you open the fan, and they protect the leaf when it is closed and rattling in a pocket. Their outer faces are where decoration goes, which is also why they are the only part of a fan that is normally lacquered or carved. The inner ribs are tapered toward the pivot so that the closed bundle is thin at the rivet end and the fan still spreads to a full arc at the top.

All the ribs share one rivet, and that single point is what makes the fan a mechanism rather than a pile of sticks. Their ends cannot separate — the rivet holds them in a stack — so the only motion available is rotation about that point. The angle between any two ribs is then set entirely by the leaf. Metal rivets are used on better fans because a bamboo pin wears oval and the fan starts to wobble at the pivot; the wobble is the first sign that a fan is finished.

The creases are the wear point. Every open and close bends the same lines, and paper fails along a fold long before it fails anywhere else. A fan is used up at its pleats: first the leaf cracks at the top of a fold, then a strip tears away from a rib, and the fan still opens but no longer holds a clean shape. Silk lasts longer but sags between the ribs, so the fan reads as soft rather than crisp. Neither material is better; they fail in different ways.

Size is not a free choice either. A fan's arc is set by how far an arm can sweep it, and the number of ribs by how fine a pleat the leaf can hold without the folds collapsing into each other. Add ribs and the fan opens more smoothly but each fold carries less paper and the leaf creases sooner. The familiar proportions — around twenty to thirty ribs over a half-circle — sit where those two limits meet.

Compared with the toys that store motion, the fan stores nothing. A tumbling doll keeps its stability in the placement of a weight; a kaleidoscope keeps its images in the angle between mirrors. The fan keeps its open state in the memory of a crease and the width of a glued strip. Fold it and the state is erased; open it and the same geometry comes back, exactly, every time.

That is the whole appeal of the object. It is a piece of engineering made almost entirely of paper, in which the only rigid parts are the sticks and the only fastener is one rivet. Everything else — the stiffness, the shape, the way it snaps to a half-circle and stays there — is done by folds that were put in deliberately, and by a strip of glue placed a few centimetres higher than a first attempt would put it.